The Etch-O-Matic
PERMANENTLY MARKS ANYTHING METAL IN SECONDS!
The Etch-O-Matic will etch anything that can be typed, written, drawn, or photo processed (on a special stencil) into the surface of anything made of metal: including tools, instruments, equipment, or manufactured parts. Your marks can be names, numbers, designs, logos, trademarks or even your own signature!
Using an electro-chemical principle, the new Etch-O-Matic can etch as deep as .003" of an inch in less than 30 seconds, or mark the hardest tool steel and carbides almost instantly. It marks any flat or round metal surface down to 1/16" diameter and any metal thickness from thin foil up to the largest castings easily. Most marks, which look like printing or engraving, take about 3 to 20 seconds (the longer dwell times are for deep etching) and are permanently etched into the tool or manufactured part surface.
BUY NOWFAST AND VERY EASY TO USE!
The Etch-O-Matic is fast and easy to use. Anyone in your organization can become an expert in just minutes and produce professional looking marks quickly. In fact, Etch-O-Matic is by far the easiest marking system to learn that is available today! You will also find that Etch-O-Matic, while being the fastest way to make permanent marks on anything metal, is by far the least expensive method on the market today. Your marks will cost just fractions of a cent to produce, and you will be extremely pleased with the result.
MARKING WITH GROUND PLATE
Simply lay the tool or part on the ground plate and touch Etch-O-Matic to it for a few brief seconds and your mark is permanently etched into the surface.
MARKING ROUND SURFACES
Drill bits, milling cutters, tubing, pipe or nearly anything round can be easily marked by "rolling" the mark on as shown above.
MAKES DEEP ETCH MARK
Etch-O-Matic marks many metals as deep as .003" with deep etch adapter clip, a mark that can only be removed by grinding a major part of the surface away.
IT'S THAT SIMPLE
Etch-O-Matic and the electro-chemical marking system has been proven over and over again during our 36 years in business as the best way to permanently mark anything metal.
COMPARES WITH LASER MARKS
Most marks made by the Etch-O-Matic will compare favorably with laser marks on metal, and are easier and sometimes even faster to make. You have very likely seen marks made by Etch-O-Matic hundreds of times before, especially since the marks are used so often in commerce today.
If you have ever seen a feeler gauge, drill bit, milling cutter, saw blade, knife blade, ball bearing race, carbide cutter or thousands of other types of metal tools, parts, instruments or equipment then you have probably seen marks made by the Etch-O-Matic system.
In fact, Etch-O-Matic has created marks in a percentage of all of the cars, trucks, commercial and military aircraft, submarines, hospital surgical instruments and implant devices. Etch-O-Matic has even been used to mark the nose cone of the space shuttle! (Yes, NASA called and said that they used an Etch-O-Matic to mark an inspection date and number in the nose cone of the space shuttles.)
EXAMPLES OF ETCH-O-MATIC MARKS
Etch-O-Matic makes a Black Mark on almost any metal
Etch-O-Matic makes a Clear Deep Etch to .003" on metals
Etch-O-Matic makes a Deep Etch Black Mark on metal
Etch-O-Matic makes a Frosty Mark on mirror finish metal
Tool and Equipment Marking
Here are examples of permanent marking that you can easily do in your own shop in just seconds! Now all you do is create your own design, logo or trademark on your computer and then by using a new stencil maker and the Etch-O-Matic you can put it on your tools, metal parts or equipment for less than a cent per mark in seconds! It is easy, quick, inexpensive and professional... and you can do it on you own!
MAKING DURA-FILM STENCILS
Process takes about three minutes
(Note: We are using large type so it will photograph easily).
Learn more about: Dura-Film stencils
Your Artwork... First make your copy on your computer. Here is a simple A B C made large to show in the photo. You can make any line drawing, logo, trademark or simple message you wish. There is not much limit except photos are difficult and very thin lines are hard to mark.
Transparency... Next print out your copy on a transparency (which comes in the kit) and place the transparency copy on a piece of unexposed Dura-Film stencil (which also comes in the kit), and finally place a glass plate on top.
U.V. Exposure Unit... Next place the tray in the 440 Dura-Film stencil maker and turn on exposure unit for about three minutes.
Develop Your Stencil... Next remove stencil and develop for 30 seconds to a minute. Stencil is then ready to use to mark your knives or anything metal.
Permanently Marked... Here we are marking a saw blade since it is large enough to make a good photo. You simply lay the stencil on the blade, wet the Etch-O-Matic pad (on bottom) with electrolyte, then place the Etch-O-Matic on the stencil, ground for a few seconds and then remove and your blade is permanently marked.
Here Are The Most Popular Etch-O-Matic Kits
Combined below with the new stencil makers for special combo offers you MUST SEE!
Etch-O-Matic Starter Kit
Lowest priced kit available anywhere, and it does the job in industry, in plants, machine shops, and everywhere metal marking is needed. The marker unit is 10 volts, 2 amps, and is excellent for light duty marking of tools and parts. (Transformer is inside marker unit)
KIT CONTAINS: Etch-O-Matic marker with standard head marking size 7/8" x 13/4";
electrical cord; ground plate; 2 oz. electrolyte solution in plastic bottle; 10 special
stencils; neutralizer; deep etching adapter clip; and complete instructions.
Each kit will make approximately 1,000 marks before refill supplies are needed.
Unit is 110 Volts standard, but is available in 220 volts for $20 more.
Etch-O-Matic Super Kit
HEAVY DUTY... INDUSTRIAL QUALITY
BEST VALUE ON THE MARKET TODAY!
NEW Super Etch-O-Matic is a powerful, 15-Volt, 10-Amp, heavy duty, industrial quality marking system that can stand up to continuous duty production line marking. It can make fast A.C. marks, then change instantly to deep etch marking down to .003" deep. It can make large marks 2" x 4" or larger (with optional purchase of medium or large grid kits) for trademarks or etch hard-to-mark coatings like black oxide quickly. This is a solid, "no frills" etcher that is priced $200 to $300 below similar kits on the market today.
KIT CONTAINS: One 15-Volt, 10-Amp. marker unit with external transformer; adapter clip for deep etch marking; ground plate; 8-oz. general purpose electrolyte; 8-oz. neutralizer; extra pads; 100 pak special stencils; complete instructions; and is packed in sturdy plastic carrying case.
Unit is 110 Volts standard, but is available in 220 volts for $20 more.
SUPER INDUSTRIAL KIT
THE NEW SUPER ETCH-O-MATIC INDUSTRIAL KIT combines the best of both of the
two kits above and gives you enough supplies to mark almost any type of metal
in the average plant. It also provides great value because you get the Starter Kit
10-volt / 2-amp Unit included FREE in the kit. Also included is a large 2" x 4" grid
that allows you to mark much larger areas at the same time.
This is an excellent value at this low price!
KIT CONTAINS: 1 Super and 1 Regular Etch-O-Matic marker along with an adapter clip for deep etch marking; ground plate; 8 oz general purpose and stainless steel electrolyte; two (2) 100 paks stencils; 4 oz. of aluminum, black oxide, and brass, copper & bronze electrolyte; 1 large 2" x 4" grid with stencils and pads to fit; 8 oz. neutralizer; 2 neutralizer powder paks; 1 extra regular grid; and complete instructions.
Unit is 110 Volts standard, but is available in 220 volts for $20 more.
440 STENCIL MAKER KIT CONTENTS
ONLY $209.95 TODAY!
- 1 UV Exposure Unit in Aluminum Frame Measuring 5"x6"x12" High with Electric Cord, Switch and Special 365 Nanometer Ultra-Violet Bulb (120 Watts)
- 1 Aluminum Exposure Tray with Compression Foam and Glass Top
- 1-16oz. Bottle Stencil Developer
- 1 Plastic Developing Tray with Lid
- 2 White Developer Sponges
- 1 Digital Timer
- 10 Unexposed Universal Stencils 5"x6"
- 2 FREE Samples of Universal Stencils FOR PRACTICE
- 5 Sheets Transparency Film For Your Copy (8 1/2"x 11")
- 1 Sample Glass Etching Kit with Etching Cream
- Complete Instructions
- ****NOTE: 440 Stencil Maker is Only Available In 110 Volt Configuration.****
- ****If You Use 220 Volts You Will Need a Step Down Transformer.****
Our Special Combination Unit Deals
Now you can combine the two Etch-O-Matic kits above with The Mark 440 Stencil Maker into a COMBO KIT shown below and receive even greater special discounts for today! Also you will qualify for the special 20% next order discount!
MARK 440 U.V. STENCIL MAKER & ETCH-O-MATIC STARTER KIT COMBO
MARK 440 U.V. STENCIL MAKER & SUPER ETCH-O-MATIC KIT COMBO
IMPORTANT NOTE
Today's Special - With each combo kit purchased today (Etch-O-Matic & Stencil Maker Combined) you will receive a 20% discount coupon for Etch-O-Matic kits or supplies ON YOUR VERY NEXT ORDER (NOT THIS ORDER) We do not guarantee this offer will be available tomorrow! DON'T MISS THIS SPECIAL OFFER TODAY!
Martronics Corporation is an expert in etching and marking metal, multi-tools, & craft-stencils with paint.
Save money on your auto insurance. Check out our VIN Etching Kits on sale for $15.45.
Our new Glass Etching Kits let you put your artwork on glass in minutes.
The Etch-O-Matic Marking System is an inexpensive alternative to laser etching and laser engraving.